Fiber Optical Delay Unit IEEE C37.34
Fibersystem 21-224 is an electro optical multiplexer between one G.703/704 E1 and two IEEE C37.94 optical ports wich are fully mapped into the G.704 standard frame structure of the E1 port, allowing for further SDH/ PDH multiplexing and de-multiplexing.
21-224 derives it synchronization from the network port (E1) or from an internal 2048Kbps PDH compliant clock enabling it to be used in leased line applications using electrical E1 modems such as SHDSL and alike.
Product Description
- Two independent IEEE C37.94 (C3794) fiber optical connections over a single E1
- Standards compliant for power substation installations
- 19″ mounting with only 200mm depth
- Single power supply range from 48VDC to 230VAC
Technical Data & Features
Fiber optical link
- Data Speed 2048kbps
- Protocol IEEE C37.94
- Fiber Multi mode 50/125µm or 62,5/125µm, ST-connector
- Optical System Budget 13dB in 62,5/125µm. 9dB in 50/125µm fiber
- Typical distance 0-2km (3dB system margin for 50/125µm and 6dB for 62,5/125µm)
Galvanic
- Galvanic Data speed 2048kbps
- Galvanic Protocol G.703, E1
- Connector 2 x BNC , Coaxial cable
Power Supply
- DC 48V DC to 250V DC, ±20%
- AC 230V AC , ±20%, 50 60 Hz
- AC-connector IEC 320, 3-pin
Environmental
- Operating Temperature Range -25 to +55°
- Storage Temperature Range -40 to +85°
- Relative Humidity Operating 5 to 95%
- Relative Humidity Storage 5 to 95% non condensing
CE compliance
- Immunity EN 61000-6-2
- Emission EN 61000-6-4
- LVD EN 50187; RIV=250 V OVC=III
Mechanical
- Vibration IEC 60255-21-1 Class 2
- Shock IEC 60255-21-2 Class 2
- Seismic IEC 60255-21-3 Class 2
EMC compliance
- ESD IEC 60255-22-2 Class 3, contact 6kV, air 8kV
- Radiated IEC 60255-22-3 / IEEE/ANSI C37.94.2; 35V/m
- Burst Power IEC 60255-22-1 Class III
- Burst Communication IEC 60255-22-1 Class II; 0,5kV diff; 1kV common mode
- Fast Transient Power IEC 60255-22-4 Class IV
- Fast Transient Communication IEC 60255-22-4 Class II; 1kV
Insulation
- Dielectric Test IEC 60255-5, 2,0kV 1min
- Impulse Voltage Test IEC 60255 / EN50178 5kV / 6 kV
- Insulation Resistance IEC 60255-5; > 100Mohm at 500VDC
Dimensions and Weight
- Physical size Height 45mm, Width 483mm, Without brackets 380mm), Depth 173mm
- Weight 3 kg
Fo converter IEEE C37.94 and E1 over Synchronous Ethernet (SyncE)
SyncE is an electro-optical converter between two IEEE C37.94 optical ports and/or G.703/704 E1 and synchronous Ethernet and reverse. Both channels are transparently converted into UDP packets and back. Standards compliant for power substation installation.
Fiber Optical Extender 80-120km
Fibersystem 21-223 SM/SM Extender (converter) is intended to extend optical reach for low speed data signal into long haul distances. Using a 21-223 the optical short reach signals can be sent without the need for additional and expensive communication systems normally found in long haul communications. When combined with the other products in Fibersystems teleprotection communication product line this converter allows a...
Fiber Optical Converter G.703-C37.94 E1 820nm Multimode
The 21-219 Fiber Optic IEEE C37.94 – G.703 E1 Converter extends distance and provides galvanic isolation between teleprotection equipment and the telecom network in substation environments. Its two independent IEEE C37.94 ports can be used for network redundancy or cross-redundancy in dual installations, ensuring high system reliability. The converter also works seamlessly with the 21-216 Fiber Optic IEEE C37.94 – G.703 64...
Fiber Optical Conv G.703 Codir C37.94 MM
The 21-216 Fiber Optic G.703 Codirectional – IEEE C37.94 Converter is an electro-optical interface converter between G.703 Codir. 64 kbps (balanced) and IEEE C37.94 N×64 kbps optical interfaces. It extends the reach of balanced G.703 connections up to 2 km, ensuring interference-free, cost-effective transmission without signal degradation. The unit supports all IEEE C37.94 channel configurations and is easy to set up. The...
